Vitrified Parking Tiles

Product Image

Application Areas

Product Features

Vitrified parking tiles offer perfect solution for our outdoor and parking tiles. These tiles come with enhanced qualities – they are hard, dense, strong and highly stain-resistant. Vitrified tiles are often used outdoors due to their water and frost resistance. These floor tiles are made to withstand extreme climatic conditions.

PRODUCT FEATURES:

● Versatility and durability is good.

● Waterproof

● Fire resistance.

● High strength and Anti-skid

● Eco-friendly

● Scratch and stain resistant

● Chemical Resistant

● Easy to clean and maintenance

● Non porous and impact resistant.

● High flexural strength

● Highly abrasion resistant.

● Heavy load bearing

● Gives a great degree of traction to vehicle wheels

Product Information

PURPOSE:-

● To provide a smooth ,clean ,impervious floor.

● To provide a colourful ,attractive and hard surface.

● To provide anti skid surface

● It also provides a walking surface.

● Enhance the beauty of the floor.

APPLICATION AREAS:-

⮚ Parking area and outdoor space

⮚ Swimming pool deck

⮚ Lobbies and terrace

⮚ Office ,shopping mall and commercial parking areas

⮚ Landscaping and walkways

⮚ Train and bus platform

⮚ Vehicle workshop and automobile plant

⮚ Public spaces and porch.

⮚ Pool surround and sit-out

Technical Information

INSTALLATION METHOD:

  1. The ground should be compacted properly by ramming and applying
  2. Water on it as per the standard practice to create a firm base. Ensure that there is no settlement of base. Also ensure the natural slope for drainage.
  3. Please lay the tiles on the substrate to match the colour properly before actual fixing.
  4. For low pedestrian traffic, on this base apply 4” to 6” thick BBC (Brick Bats Cement Concrete).
  5. For medium traffic floors, on the BBCC base, make 3” thick PCC (Plain Cement Concrete) in 1:3:6.
  6. For heavy duty traffic, make 4” thick RCC (Reinforced Cement Concrete) in 1:2:4. The RCC should be laid such that the proper line and level is attained.
  7. Prepare base mortar by mixing sand and cement in 1:4 proportions.
  8. Lay the mortar on the substrate prepared as mentioned above in required line and level. It should be noted that in any case the bed mortar thickness should be more than 1” thickness.
  9. Mark the centerline and fix the tiles on all the corners and center in the required level. Preferably, start fixing tiles parallel to longer span.
  10. Prepare thick cement paste by mixing water & cement. Apply this paste on the backside of the tile to fix it.
  11. Fixing of tile has to be done with a minimum gap of 8mm. We do not recommend tiles to be laid without a gap (to provide for expansion due to sunlight/heat).
  12. Lay the tiles on this firm base and ram lightly with the help of a rubber hammer or trowel from top. See that the tile top surface is laid in the required line and level with proper joint gap.
  13. Utmost care should be taken while fixing other tiles in terms of matching lines and keeping exact joint width between tiles. (For maintaining joint width spacers are recommended of required joint thickness).
  14. After 24hrs of applying a joint filter ,wash the surface with water and clean the surface with the help of a wet sponge.

INSTALLATION MATERIALS:

❖ tile spacers

❖ sponge

❖ bucket

❖ notched trowel

❖ tile cutter

❖ broom

❖ chalk line

❖ thin-set mortar

❖ grout

❖ tiles

❖ Tape

❖ Pencil

Maintenance and Warranty

MAINTENANCE:-

DO'S:-

⮚ Sweep, dust, or vacuum, your floor daily if needed.

⮚ After installation, apply tile and grout sealer in order to maintain your tiled surfaces.

⮚ Rugs or mats may be used (especially in entryways and exits) to avoid unnecessary dirt and grit entering the house, this may also help avoid slipping or scratching.

⮚ Always perform routine cleaning maintenance to your tiled surfaces. Conduct a routine maintenance check of your tile for dirt, stains, or cracks.

⮚ Always use dirt-free, clean water during cleaning. Ensure you frequently make a new cleaning solution to avoid reintroducing dirt to the tiled surface.

DONT'S:-

⮚ Avoid using steel wool, scouring powders, or other abrasives

⮚ Don’t use bleach or ammonia-based cleaners

⮚ Do not clean glazed tile with oil-based cleaners

⮚ Don’t let spills sit, try to clean up spills as quickly as possible

⮚ Don’t use bleach or any acidic solutions to clean your tiles: they may cause more harm than good.

⮚ Don’t use harsh scouring pads or steel wool. They may scratch and damage the surface of the tile.

⮚ Don’t assume tiles are indestructible. Though durable, they may crack and chip if they are subject to unnecessary force, weight or neglect.

WARRANTY: 1 year for colour fade

SUBBASE REQUIREMENTS: DRY , LEVELLED, NO DIRT OR GRITS, NO CRACKS, FIRM

MEASUREMENT METHOD AND UNIT:

● STEP 1: Measure the area . Use the tape measure to measure the length and then the width of the room , Making a note of measurements.

● STEP 2: Calculate the square footage.

● Step 3: Calculate amount of flooring needed.

● UNIT: SQ.FT

Shade Card : Available on Request

Maintenance Video

Installation Video